Synonymer & Information om | Engelska ordet LOWPASS

Exempel på hur man kan använda LOWPASS i en mening

• Typically in electronic systems such as filters and communication channels, cutoff frequency applies to an edge in a lowpass, highpass, bandpass, or band-stop characteristic – a frequency characterizing a boundary between a passband and a stopband.
• The filter outputs often include a lowpass response, and sometimes highpass, bandpass or notch responses.
• Upsampling requires a lowpass filter after increasing the data rate, and downsampling requires a lowpass filter before decimation.
• The example given below can produce simultaneous lowpass, highpass, and bandpass outputs from a single input.
• The LFO is routable to a comprehensive amount of options, including: the bender, VCO pitch, pulse-width, both highpass and lowpass filter cutoff, and the VCA.
• It also utilized three parallel band-pass filters, one lowpass filter, and one highpass filter with fixed cutoff frequencies per voice and an electro-mechanical 6-channel vibrato unit operating on pairs of adjacent oscillators.
• Each voice has two VCOs, one VCA, one 24 dB/octave lowpass VCF, two LFOs, two ADSRs, noise generator, sync VCO 1 to VCO 2.
• Last but not least, the humble "big muff pi" style tone control immediately preceding the output buffer is a fixed cutoff lowpass filter and a fixed cuttoff highpass filter which attenuate either the low or high end, depending on the position of the potentiometer.
• Filter: 2-pole multimode resonating filter per voice, 4-pole lowpass resonating filter per voice (32 total).
• On November 25, 2022, reFX announced they had revived the Vanguard synthesizer as Vanguard 2 with an updated vector-based user interface, in addition to 10 new wavetables by Mirko Ruta, 24db ladder filters for lowpass and highpass also made by Mirko Ruta, a new reverb named RutaVerb also by Mirko Ruta replacing the old Freeverb-powered reverb and a distortion effect alongside 136 new factory presets made by Mirko Ruta and other modulation features, such as a new 3rd envelope and a new delay type intended to widen a sound.
• In JPEG XR, 4 × 4 blocks are grouped into macroblocks of 16 × 16 samples, and the 16 DC coefficients from the 4 × 4 blocks of each macroblock are passed through another level of frequency transformation, leaving three types of coefficients to be entropy coded: the macroblock DC coefficients (called DC), macroblock-level AC coefficients (called "lowpass"), and lower-level AC coefficients (called AC).
• By shifting the frequency of the reference beam, the lowpass filter becomes a bandpass filter centered at the detuning frequency, and selective narrowband detection and imaging can be performed.
• Like Laguerre filters, Kautz filters can be implemented using a cascade of all-pass filters, with a one-pole lowpass filter at each tap between the all-pass sections.
• A development on this method with improved invertibility involves performing CQT (via fast Fourier transform) octave-by-octave, using lowpass filtered and downsampled results for consecutively lower pitches.
• While software implementations are also possible, operations in the DDS, multipliers and input stages of the lowpass filters all run at the sampling rate of the input data.
• In order to create a multirate narrow lowpass FIR filter, we need to replace the time invariant FIR filter with a lowpass antialiasing filter and use a decimator along with an interpolator and lowpass anti-imaging filter.
• The combination of 3-D HWT wavelets is done in a manner to ensure that the resultant wavelet is lowpass along 1-D and bandpass along 2-D.
• This is achieved by bypassing the highpass, lowpass, preemphasis, and deemphasis filters normally contained in the microphone and speaker circuits of an FM transmitter and receiver.

Förberedelsen av sidan tog: 549,01 ms.